NABL-accredited calibration lab · ISO/IEC 17025 NABL accredited · On-site across India On-site calibration across India
Equipment guides

Ventilator Calibration: Which Parameters Are Checked

The parameters checked during ventilator calibration, from tidal volume, rate, PIP, PEEP and oxygen percentage to alarms and battery backup, the test equipment used, typical limits and what the report should record.

  • By the Shiwi engineering team
  • 7 min read
Blog banner with an ECG trace and the title Ventilator Calibration: Which Parameters Are Checked

Ventilator calibration checks that the breaths a ventilator delivers match its settings and that its own monitoring and alarms report them correctly. An engineer connects the ventilator to a gas flow analyser and a test lung, then compares measured tidal volume, respiratory rate, PEEP, peak inspiratory pressure and oxygen percentage with what was set and what the ventilator displays. Alarms, battery backup and electrical safety are checked during the same visit.

This article goes through each parameter, the equipment used to measure it, and what a useful calibration report looks like for an ICU, emergency department or operating theatre.

Why does a ventilator need calibration if it runs its own self-test?

Most modern ventilators run a self-test or pre-use check, and these should be done as the manufacturer instructs. A self-test confirms the machine’s internal sensors and valves are responding. It does not compare the ventilator against an independent, calibrated reference.

Flow and pressure sensors can drift, oxygen sensors age, valves wear and small leaks develop. A ventilator can pass its own check while delivering volumes that differ from the setting. Periodic testing against a reference analyser is how a biomedical department gets evidence that the delivered breath is what the clinician asked for.

Which parameters are checked during ventilator calibration?

The exact list depends on the ventilator and its modes, but the core parameters are the same across most critical care units.

Tidal volume

Tidal volume is the volume of gas delivered in each breath. The engineer sets a volume-controlled mode at several tidal volumes and compares the analyser reading with the setting and with the ventilator’s displayed value. For neonatal or paediatric ventilators, smaller volumes are tested using a suitable test lung.

Respiratory rate

The analyser counts breaths per minute and compares the result with the set rate. Inspiratory time and the inspiratory-to-expiratory (I:E) ratio are usually checked alongside rate, because together they determine breath timing.

Peak inspiratory pressure (PIP)

PIP is the highest airway pressure reached during inspiration. In pressure-controlled modes, the engineer checks that the delivered pressure matches the set pressure. In volume modes, the analyser’s reading of peak pressure is compared with the ventilator’s own display.

PEEP

Positive end-expiratory pressure is the pressure the ventilator holds in the airway at the end of each exhalation. It is checked at a few settings, because a ventilator that holds PEEP accurately at one level may not at another.

Oxygen percentage (FiO2)

The analyser’s oxygen sensor measures the oxygen concentration delivered and compares it with the set FiO2 at several points across the ventilator’s range. This also tests the ventilator’s air-oxygen blender and its internal oxygen sensor, which is a consumable part on many models.

Other parameters

Depending on the ventilator, engineers may also check minute volume, peak flow, mean airway pressure, trigger sensitivity and the pressure-relief valve. ECRI’s inspection procedure for intensive care ventilators lists tidal volume, pressure, rate, I:E, PEEP, flow, trigger sensitivity and oxygen delivery among the controls to verify.

What equipment is used to test a ventilator?

A gas flow analyser is the main instrument. For example, the Fluke Biomedical VT650 is described by its maker as an analyser for testing gas flow and respiratory medical equipment, including neonatal, mechanical and high-frequency ventilators. Analysers of this type measure flow, volume, airway pressure and oxygen concentration, and calculate breath parameters such as tidal volume, rate, I:E ratio, PIP, PEEP and mean airway pressure.

The analyser is used with a test lung (lung simulator), ideally one with adjustable compliance and resistance so the ventilator can be tested under more than one lung condition. ECRI’s procedure also recommends a filter between the ventilator and the tester. An electrical safety analyser is needed for the safety tests.

The analyser itself must be within its calibration period. A reading is only as trustworthy as the instrument taking it.

What are acceptable limits?

The first reference is always the manufacturer’s service manual, which gives the accuracy each control and monitored value should meet. Where general guidance is needed, ECRI’s BiomedicalBenchmark inspection procedure for intensive care ventilators says that measured values should typically be within 10% of settings, with rate within 1 breath per minute of the set rate (or 2 breaths per minute at high rates). For monitored values, ECRI suggests the display should be within 10% of the simulated value or within the manufacturer’s stated accuracy.

The international design standard for these devices is ISO 80601-2-12, which covers basic safety and essential performance of critical care ventilators. Anaesthesia ventilators, home-care ventilators, CPAP and several other types fall under separate standards, so the right reference depends on the device.

How are ventilator alarms tested?

Alarm testing is as important as measuring the breath. The engineer sets alarm limits and then creates the condition that should trigger each one, for example by changing test lung compliance, disconnecting the circuit or occluding it. Typical checks include:

  • High and low airway pressure alarms.
  • Low and high tidal or minute volume alarms.
  • Circuit disconnection alarm.
  • Apnoea alarm.
  • High and low oxygen alarms.
  • Gas supply failure (air and oxygen).
  • Mains power loss, with automatic switchover to battery, and low-battery alarm.

ECRI also advises confirming that critical alarms cannot be silenced without a warning or automatic reactivation, and that alarms are loud enough to be heard in the clinical area.

Checklist: ventilator calibration report

Section What should be recorded
Identification Make, model, serial number, asset number, location, hour meter reading
Physical inspection Housing, casters, mounts, power cord, filters, circuit, connectors, labels
Self-test Result of the ventilator’s own self-test or pre-use check
Tidal volume Set, measured and displayed values at each test point
Respiratory rate and I:E Set, measured and displayed values
PIP and PEEP Set, measured and displayed values at each test point
Oxygen percentage Set and measured FiO2 at each test point
Alarms Each alarm tested, with pass or fail
Battery Switchover on mains loss, battery operation, low-battery alarm
Electrical safety Protective earth resistance, leakage current, insulation resistance
Reference equipment Analyser and safety tester used, with their calibration due dates
Result Overall pass or fail, limits applied, engineer’s name, date, next due date

Electrical safety deserves its own attention on any device connected to a patient. Our guide to electrical safety testing of medical equipment explains the measurements.

How often should ventilators be calibrated?

Follow the manufacturer’s schedule, which for ventilators is sometimes based on operating hours as well as time. ECRI’s procedure uses a 12-month interval and recommends recording the hour meter reading at each inspection. Most departments also test after any repair, after replacing a flow or oxygen sensor, and before returning a ventilator to service after a long period in storage. ECRI notes that a used ventilator with an unknown maintenance history should have all scheduled tasks completed before use.

Calibration fits within a wider maintenance plan that includes filter and sensor replacement and planned service visits. Our preventive maintenance schedule for biomedical equipment shows how to organise these tasks across a hospital’s inventory.

Does the same approach apply to BiPAP and CPAP?

The principle is the same: compare delivered pressure, and where relevant flow and oxygen, against a reference. The parameters and limits differ, and these devices fall under different standards from critical care ventilators. See our pages on BiPAP calibration and CPAP calibration.

Safety note: This article is general guidance. Ventilators are life-support equipment. Testing, adjustment and repair should be carried out only by qualified engineers using calibrated analysers, following the manufacturer’s service manual for the specific model. Never test a ventilator while it is connected to a patient.

Arranging ventilator calibration

Shiwi Enterprises is a NABL-accredited calibration laboratory (ISO/IEC 17025) in Jaipur. On-site, our engineers check PEEP, PIP, oxygen percentage, respiration rate and tidal volume against calibrated reference analysers, along with electrical safety, and issue a calibration certificate for each ventilator for NABH and internal audits. We work with hospitals across India, including in small towns. Visit our ventilator calibration page or request a quote.

Frequently asked questions

Which parameters are checked in ventilator calibration?

The core parameters are tidal volume, respiratory rate and I:E ratio, peak inspiratory pressure, PEEP and oxygen percentage (FiO2). Depending on the model, minute volume, flow, mean airway pressure and trigger sensitivity are also checked, along with alarms, battery switchover and electrical safety.

What equipment is used to calibrate a ventilator?

A gas flow analyser, such as the Fluke Biomedical VT650, used with a test lung (lung simulator), plus an electrical safety analyser. The analysers must themselves be within their calibration period.

What accuracy should a ventilator meet?

The manufacturer's service manual sets the limits for each model. As general guidance, ECRI's inspection procedure for intensive care ventilators says measured values should typically be within 10% of settings, with rate within 1 breath per minute of the set rate, or 2 at high rates.

How often should ventilators be calibrated?

Follow the manufacturer's schedule, which may be based on operating hours as well as time. ECRI's procedure uses a 12-month interval. Ventilators should also be tested after repair or sensor replacement and before returning to service after storage.

Request a calibration quote

List your equipment with make, model and quantity, and tell us your city. We reply with a quote and a visit plan.

    Planning calibration before your next audit?

    Send us your equipment list and city. We will reply with a quote and a visit schedule.

    Scroll to Top