What Is Medical Equipment Calibration and How Often Should It Be Done?
What medical equipment calibration involves, which devices need it, and how to set calibration intervals based on manufacturer guidance, risk, usage and calibration history.

Medical equipment calibration is the process of comparing what a device measures or delivers against a reference of known accuracy, recording the difference, and adjusting the device where needed so it stays within its specified limits. There is no single interval that suits every device: start from the manufacturer’s recommendation (many hospitals use a yearly cycle where none is given), then shorten or extend it based on risk, usage and calibration history. Equipment should also be checked after any repair, damage or doubtful reading.
This guide explains what calibration covers, how it differs from routine maintenance, and how to set sensible intervals for the equipment in your hospital, lab or clinic.
What does calibration of medical equipment actually involve?
Every measuring or therapy device drifts over time. Sensors age, components wear, and transport or rough handling can shift readings. Calibration tells you how far a device has moved from the true value and whether it is still fit for clinical use.
A typical calibration visit includes:
- Comparison against a reference. The device is tested against a reference analyser or simulator whose own calibration is traceable to national standards. For example, a patient monitor is connected to a patient simulator that generates known ECG, blood pressure and SpO2 signals.
- Recording “as found” results. Readings are noted before any adjustment, so you know whether the device was in tolerance during the period it was in use.
- Adjustment where possible. If a parameter is out of tolerance and the device allows it, the engineer adjusts it following the manufacturer’s procedure, then re-tests.
- Electrical safety testing. For mains-powered equipment, checks such as leakage current, protective earth resistance and insulation resistance confirm the device is safe for patients and staff.
- A calibration certificate. The results, reference equipment used, measurement uncertainty and date are documented for each instrument.
The World Health Organization’s guidance on maintenance programmes makes the same distinction between the two kinds of check: performance inspections ensure equipment is operating correctly, while safety inspections ensure it is safe for both patients and operators.
Calibration, maintenance and repair are not the same thing
These terms are often used together, but they answer different questions:
- Calibration: is the device measuring or delivering accurately?
- Preventive maintenance: is the device being cleaned, inspected and serviced so it lasts longer and fails less often?
- Repair (corrective maintenance): the device has failed or shows a fault, so what needs to be fixed?
A device can be well maintained and still read inaccurately, which is why calibration needs its own schedule and its own records. Our repair and preventive maintenance services page explains how the two fit together in practice.
Which medical equipment needs calibration?
Any device that measures a physiological value or delivers a controlled dose of energy, fluid, gas or heat should be on your calibration list. The table below shows common examples and the kinds of parameters that are usually checked. Exact test points depend on the make, model and the manufacturer’s specification.
| Equipment | Typical parameters checked |
|---|---|
| Patient monitor | ECG heart rate, non-invasive blood pressure, SpO2, temperature, alarms |
| Defibrillator | Delivered energy at selected settings, charge time, synchronised mode |
| Infusion pump and syringe pump | Flow rate accuracy, occlusion pressure and alarms |
| Ventilator | Tidal volume, pressure, respiratory rate, oxygen concentration, PEEP |
| Electrosurgical unit | Output power across modes, high-frequency leakage |
| Infant incubator | Air temperature, humidity, alarm function |
| ECG machine | Amplitude, heart rate accuracy, recording speed |
| Pulse oximeter | SpO2 and pulse rate against a simulator |
You can see the full range we cover on our equipment we calibrate page.
How often should medical equipment be calibrated?
The honest answer is that it depends on the device and how it is used. International guidance on recalibration intervals, published jointly as ILAC-G24 / OIML D 10, says the initial interval should rest mainly on a risk assessment, and that intervals should then be reviewed using the device’s calibration history.
Factors that should shape your interval
Drawing on that guidance, consider:
- Manufacturer’s recommendation. Start here. The service manual often states a calibration or performance verification interval.
- Clinical risk. A device that delivers energy or drugs, or supports breathing, carries more risk if it drifts than a device used only for general observation.
- Intensity of use. A monitor running around the clock in an ICU sees far more use than one in a day-care room.
- Environment and handling. Heat, dust, humidity and frequent movement between wards all increase drift.
- Tendency to wear and drift. Some sensors and mechanisms are known to drift faster than others.
- Calibration history. If a device has been found out of tolerance at its last check, shorten the interval. If it has been stable over several cycles, you may have grounds to keep or extend it.
- Accreditation and regulatory expectations. Your NABH, NABL or internal quality requirements may set expectations of their own.
When to calibrate outside the normal cycle
Do not wait for the scheduled date if any of the following happens:
- The device is new or has just been installed, before it goes into clinical use.
- It has been repaired, especially if a sensor, board or power section was replaced.
- It has been dropped, exposed to fluid or moved between sites.
- Clinical staff report readings that do not match the patient’s condition or another device.
- A software or firmware update has been applied.
The electrical safety standard for medical equipment in service, IEC 62353, covers testing before equipment is put into service, during maintenance and inspection, and after repair. It is a useful reference for building safety checks into the same trigger points.
How do you set up a calibration schedule that works?
A schedule only helps if it reflects what is actually in your building. A practical approach:
- Build a complete equipment inventory. Record each device with its make, model, serial number, location and asset ID.
- Classify by risk. Group devices into high, medium and low risk based on what they do and the harm a faulty reading could cause.
- Assign an interval to each group. Use the manufacturer’s recommendation as the baseline and adjust for risk and use.
- Plan visits by area. Grouping ICU, OT and ward equipment into planned visits reduces downtime and makes on-site calibration more efficient.
- Label each device. A calibration sticker with the date done and date due helps staff spot overdue equipment.
- Keep certificates together. File each certificate against the asset record so you can produce it quickly during an audit.
- Review once a year. Look at which devices failed calibration and adjust intervals accordingly.
For a closer look at how this ties into NABH documentation, see our NABH calibration requirements checklist. If you are building a combined maintenance plan, our guide to a biomedical preventive maintenance schedule covers the servicing side.
This article is general guidance. Calibration, adjustment and electrical safety testing should follow the manufacturer’s service manual and be carried out by qualified biomedical engineers using suitable reference equipment.
What should a calibration certificate show?
A certificate is your evidence that the work was done properly. At a minimum, check that it includes:
- The device’s description, make, model, serial number and asset ID
- The date of calibration and the location where it was done
- The reference equipment used, with its own calibration traceability
- Results for each parameter, with the tolerance or acceptance limit
- Measurement uncertainty
- A clear pass or fail statement, and any adjustments made
- The name and signature of the engineer and the authorising person
If the calibration is done under NABL accreditation, the certificate should also carry the NABL accreditation symbol for parameters within the lab’s accredited scope. We explain the practical difference this makes in NABL vs non-NABL calibration.
Does calibration have to be done in a lab?
No. Most hospital equipment can be calibrated on site, which avoids taking critical devices out of service for days and removes the risk of damage in transit. The calibration provider brings the reference analysers to your facility and tests each device where it is installed.
Shiwi Enterprises is a NABL-accredited calibration lab (ISO/IEC 17025) based in Jaipur. Our engineers carry out on-site calibration across India, including hospitals and clinics in small towns and villages, using calibrated reference analysers. Each instrument receives its own calibration certificate for NABH and internal audits, and the same team can handle repair and preventive maintenance if a device fails its checks.
Plan your next calibration cycle
If you are setting up a calibration schedule for the first time, or your current certificates are close to their due dates, we can help you plan an on-site visit that covers all your equipment in one go. See how our calibration service works, or request a quote with a list of the equipment you need calibrated.
Frequently asked questions
What is medical equipment calibration?
It is the comparison of a device's readings or output against a reference of known accuracy, traceable to national standards, with the results recorded and the device adjusted where needed so it stays within its specified limits.
How often should medical equipment be calibrated?
There is no single interval for every device. Start with the manufacturer's recommendation, then adjust for clinical risk, intensity of use, environment and the device's calibration history. Many hospitals use a yearly cycle where the manufacturer gives no interval.
When should equipment be calibrated outside the normal schedule?
Before first clinical use, after repair, after the device is dropped or exposed to fluid, after a software update, and whenever staff report doubtful readings.
Can medical equipment be calibrated on site?
Yes. Most hospital equipment can be calibrated where it is installed, using portable reference analysers and simulators, which reduces downtime and transport risk.
Request a calibration quote
List your equipment with make, model and quantity, and tell us your city. We reply with a quote and a visit plan.
Keep reading
All articles-
Calibration How to Choose a NABL Calibration Lab for Your Hospital
A step-by-step guide for hospitals on verifying a NABL calibration lab, reading its scope of accreditation, and checking on-site capability, reference equipment and certificates.
-
Compliance NABH Medical Equipment Calibration Requirements: A Checklist for Hospitals
A practical checklist for NABH coordinators and biomedical engineers covering equipment inventory, calibration schedules, certificates, electrical safety and the records assessors ask for.
-
Compliance NABL vs Non-NABL Calibration: What Hospitals Should Know
How NABL-accredited and non-accredited calibration differ in scope, traceability and audit value, and how hospitals can tell which kind of certificate they hold.